As for technique, you should coat the wire and post with rosin flux prior. You can use banana plugs for this.
They are quite frequent and a cable can be hooked in two ways.
How to connect speaker wire to binding post. Connect the speaker wires to the speaker terminals on the rear of the a/v stereo receiver. Some of the speaker wires come in a tinned shape. For spring clip terminals, press down on the red (positive) or black (negative) clips and insert the speaker wire into the slot.
Make sure enough portion of the metal wire is inserted on them. So, you don’t have to do that in cases of those speaker wires. Feed the wire into the entry hole of the binding post.
Insert each side into the exposed holes. Remove the bridge plates or pins between the binding posts and connect the two sets of speaker wires to the amplifier (making sure to note the bass posts and the treble posts). They are able accommodate speaker wire connectors that require a clamping action in order to transfer a signal.
Can't find what you are looking for on do it yourself diy binding post or have a question? If you remove the binding strap and connect 1 wire (neg/pos) to the top posts and 1 wire (neg/pos) to the bottom posts and then connect both wires to the same pos/neg terminal on the amplifier/receiver, uyou are creating the same parallel connection the strap does but instead of on the speaker you are doing it at the receiver/amplifier. How to connect speaker wire to a binding post unscrew the caps covering each binding post until you expose the small hole through their centers.
Steps for connecting speaker wire to binding post terminals on subwoofers: What is more important is that all connections are clean and secure. Also, note which way you have connected up the wire in terms of polarity.
It is, in fact, easier, since you can hold the banana plug in your hand while doing it, and don’t have to bend behind your stereo or speakers. Insert each side into the exposed holes. Twist the bare speaker wire to create a single strand.
Insert each of the cables into the hole now this is the most crucial part on which the entire connection depends on.insert each of the cable openings to the relevant binding post holes. Such speaker wire connectors include bare wire, spade lug connectors, and pin connectors. Banana plugs are very convenient, but i have an affinity towards bare speaker wire.
Then tighten the outer shell of the binding post down to hold it. •bare wire inserted through the hole in the post and clamped. Connect the other end of the speaker wire to your speakers
To use spade connectors like these pictured, simply unscrew the binding post on the back of the amplifier or loudspeaker and place the fork end of the connector against the binding post shaft. Almost all the speakers have a binding post. Most loudspeaker and amplifier connectors accept multiple types of connections:
Twist the wire tightly by hand to keep the wire strands together. Just use zip ties and tie the cables up to any brackets of the drivers or on the box braces that are inside the box. Strip the speaker wire to about 3/8″ to 1/2″ length bare wire.
•bare wire wrapped around the metal post and clampled. To ensure your speakers function properly, make sure that the wire leading to the positive (red) binding post is also connected to the positive terminal of your receiver or amplifier. Then hold your iron up against the outside of the binding post by the hole the wire is looped thru.
They can also be used with pin connectors and banana connectors. You need to disconnect the speaker wire and insert it into the post hole. Also to know is, how do you wire 4 terminal.
In fact, probably the best method if you never disconnect/reconnect. For binding post terminals, loosen the red (positive) or black (negative) binding posts by turning. When done, the solder joint should have a smooth fillet (proper wetting) and not be a big blob.
•a spade lug clamped around the post. Feed your solder to the inside of the binding post at the post/ wire interface. As long as you twist them properly and leave no strands hanging outside and get the whole thing fit in the binding post and screw it tightly its the best connection imho.
As for the wires inside the speaker box. But if your in the testing stages of building, i would use the ring terminals for now and then solder them before you button up the box. Installing speaker wire onto banana plugs is very similar to connecting speaker wire to a binding post, as detailed above.